Melbourne-based · Australia-wide

Pressure equipment inspection, with a complimentary 3D scan included*

Independent, statutory and compliance inspection of pressure vessels, piping and relief devices, to AS/NZS 3788 and the applicable state/territory requirements. Melbourne-based, servicing Australia-wide. Every inspection includes a complimentary external 3D scan of your asset.

Get a quote0493 928 187Email
AICIP In-Service InspectorAPI 510 / 570 / 580 certifiedCASA-licensed drone pilot$10M PL & PI insured

// Inspection services

Statutory & compliance inspection, done properly

Independent, statutory and compliance inspection across the full life of your pressure equipment: vessels, piping and relief devices, external and internal, to AS/NZS 3788 and the applicable state/territory requirements.

Internal & External Pressure Vessel Inspection

Statutory and compliance inspection of in-service pressure vessels, internal and external, to AS/NZS 3788 and the applicable state/territory requirements, keeping plant compliant and safe to operate.

  • All vessel types: heat exchangers, air coolers, towers & columns, scrubbers, drums, separators, air receivers and boilers
  • External and internal visual, wall-thickness and damage-mechanism review; corrosion, coating and integrity assessment
  • Inspection intervals and reporting aligned to AS/NZS 3788
  • Findings tied to fitness-for-service and remaining-life decisions

Process & Utility Piping Inspection

Statutory and compliance inspection of process and utility pressure piping to AS/NZS 3788 and the applicable state/territory requirements.

  • Process and utility piping circuits and condition-monitoring locations
  • Corrosion-under-insulation (CUI) screening
  • Support, dead-leg and injection-point assessment
  • Records structured for ongoing integrity management

Pressure Relieving Devices

Statutory inspection and management of pressure relief valves and safety devices: set-pressure testing and recertification through our accredited partner network.

  • Pressure relief and safety valves (PRVs / PSVs)
  • Set-pressure (pop) testing and recertification via accredited partners
  • Register, tagging and due-date tracking
  • Test intervals aligned to your inspection program

Inspection Planning & Consultation

Planning and consultation that keep your inspection program on track and defensible.

  • Inspection planning for shutdowns, outages and turnarounds
  • Inspection consultation to support your inspection program, time-based or RBI

// Why inspect

Statutory inspections — not optional

The inspections we provide are statutory and compliance inspections, required to meet your regulatory obligations and to keep your insurance valid, and what confirms your equipment is safe to keep operating.

Regulatory compliance

Meet your duty-holder obligations under AS/NZS 3788 and your state or territory's requirements.

Valid insurance

Current, code-referenced inspection records keep your insurance cover valid and your claims defensible.

Safe to keep operating

Damage mechanisms are identified before they become failures, so your plant keeps running safely.

// Full-scope, when you need it

Backed by a network of NDT partners

When a job calls for more, we supplement the inspection with our strong network of certified, fully compliant NDT and testing partners, so you get a complete, compliant result from a single point of contact.

  • Ultrasonic testing (UT) & wall-thickness surveys
  • Radiography (RT)
  • Magnetic particle (MT) & dye-penetrant (PT)
  • Positive material identification (PMI) & hardness testing
  • Pressure relief valve testing & recertification

// See it in action

Every finding, pinned to the real 3D model

This is a real vessel scan, captured on the ground during an inspection. As it turns, every finding stays pinned exactly where it is on the asset, severity-classified. This is the live, interactive record you keep in Speqo.

1Nameplate
2Original Coating / Local Pitting
3Isolated Coating Failure
4Loose Bolting
5Corroded Bolting
6CML-05: 1.0mm
LPG-1075 · LPG storage vessel — external inspectionIllustrative demo · real 3D scan with sample findings.
CriticalMajorMinorInfo

On a live job your interactive model lives behind your Speqo login. The report travels, but the 3D record and its full history stay with the asset.

// Findings on this scan

  • 1NameplateInfo
  • 2Original Coating / Local PittingMinor
  • 3Isolated Coating FailureMinor
  • 4Loose BoltingMinor
  • 5Corroded BoltingMajor
  • 6CML-05: 1.0mmCritical

// More than a picture

A working record you can navigate

Findings linked to your documents

Every finding, CML and timeline event can link straight to the report, certificate or drawing it relates to in the asset's document repository, one click from the pin to the paperwork.

Linked scans — navigate your whole site

Start on a 3D model of your facility, find a vessel on the map and click into its own scan — then step inside to an internal scan. Models connect, so you move from the site, to the vessel, to a close-up.

Thickness, measurements & photos

Pin CMLs to track wall thickness against T-min, measure distances directly on the model, and attach site photos to any point.

The whole history on a timeline

Past inspections, repairs, alterations and re-ratings layer onto the model on a date you can scrub through. See the asset as it was at any point in time.

Share with your team

Send a read-only link so colleagues can explore the model and its findings in the browser, no login required.

Field-ready PDF export

Print the current view with its annotations, plus a table for each category, to a PDF you can take onsite or attach to a report.

// How Speqo works

From site visit to a record you can trust

Speqo turns an inspection into a living digital record of your asset: captured, checked against the codes, and kept up to date.

  1. 01

    Capture on site

    On-site inspection paired with a 3D scan, captured with the right tool for the asset to record the whole thing, including elevated and hard-to-reach areas.

  2. 02

    Inspect to the standard

    Your certified inspector assesses the equipment in accordance with AS/NZS 3788 and the applicable state/territory requirements, with every finding referenced to the relevant clause.

  3. 03

    Build the 3D model

    Scan data becomes a navigable 3D model of your equipment: a precise digital record you can revisit, measure and compare over time.

  4. 04

    Findings on the model

    Every finding is severity-classified, code-referenced and pinned to its exact location on the 3D model, nothing buried in a PDF.

  5. 05

    Report & stay ahead

    You receive a compliance-grade report and automatic reminders before the next inspection falls due, so nothing slips.

// 3D models, any asset

One vessel, or your whole facility — in 3D

We can scan a single vessel, or build a 3D model of your whole facility that connects each asset to the wider site, subject to access. And it isn't just for pressure equipment.

For pressure equipment

The 3D scan and its hosting are included, aligned to your external inspection interval, typically two years. Re-inspect with Speqo and hosting stays included; otherwise keep your assets and 3D models on a continued-hosting plan (contact us for pricing). Either way you keep your document repository and 3D-scan hosting.

No pressure equipment? We still capture it.

Focused drone missions by a seasoned inspector turn any asset into a precise 3D record. Host it on your own platform, or host it on Speqo for two years. Every capture includes two years of complimentary platform access (document repository + 3D-scan hosting).

Bridges & civil structures
Buildings & heritage facades
Chimneys, stacks & towers
Telecom & transmission towers
Wind turbines & solar farms
Jetties, wharves & marine structures

Enterprise drone capture by a licensed inspector — see the full range of drone-enabled inspections and where they fit.

Explore drone inspection services

Drone work is flown under a CASA Remote Pilot Licence.

// Your model, your history

A living record — not just a 3D model

The model isn't a one-off snapshot. It carries your asset's whole history, and it works just as well with a scan you already have.

Your inspection history, on the model

We can load your past inspections onto the model: every finding, measurement and report pinned where it belongs, on a timeline you can scrub through to see exactly how the asset has changed over the years.

Already have a 3D model? Host it with us

If your asset has been scanned before, bring your existing 3D model to Speqo and use us purely for hosting. We set the whole thing up for you: your model, documents and history, ready to explore and share with your team.

Pricing depends on your assets and scope. Enquire for a quote, or book a quick demo to see it in action.

Enquire for pricingRequest a demo

Melbourne-based, servicing Australia-wide

Based in Melbourne, Victoria, providing pressure equipment inspection and 3D scanning across Australia, from Victoria plant and refineries to interstate sites by arrangement.

  • Melbourne
  • Sydney
  • Brisbane
  • Perth
  • Adelaide
  • Darwin

Fully mobile, we service all regional areas across Australia and can mobilise anywhere your equipment is.

// Get started

Book an inspection. Get a scoped quote.

Tell us about your equipment and we'll come back with a clear, scoped quote, including your complimentary 3D model. Melbourne-based, servicing Australia-wide.

Get a quoteGet a free assessment→
0493 928 187mat@speqo.io